Better Concrete Testing Starts with Better Specimen Preparation
Marui Concrete Cylinder Grinders and Hylec Insulated Thermal Moulds – trusted solutions for concrete testing laboratories
Accurate concrete testing starts well before a specimen reaches the compression testing machine. The way concrete test cylinders are moulded, stored, handled and prepared for testing can all influence laboratory efficiency and the reliability of test results.
At Hylec Controls, we understand the importance of consistent concrete specimen preparation. That's why we supply two established product ranges to the Australian and New Zealand concrete testing industries: Japanese-engineered Marui concrete cylinder grinding machines and our own Hylec-developed insulated plastic moulds.
Both products have been developed around the practical needs of concrete laboratories, helping improve specimen preparation, handling and testing workflows.
Marui Concrete Cylinder End Grinders – precision, productivity and reliability
For more than 20 years, Hylec Controls has been supplying Marui concrete cylinder grinding machines to the Australian market.
Over the past seven years, we have sold 54 Marui grinding machines, including 28 in the last two years alone. This represents strong industry confidence in the quality, performance and reliability of the Marui range.
Our customers include some of Australia's leading concrete testing and construction materials organisations, including Construction Sciences, Boral and Hanson.
Introducing the Marui Triple Hi Kenma

The Marui Triple Hi Kenma is designed to streamline concrete cylinder end preparation by automatically grinding three specimen end surfaces at the same time.
Rather than preparing individual cylinders one at a time, the machine allows three specimens to be processed in a single grinding cycle. This can significantly reduce operator involvement, preparation time and laboratory floor space.
Technical features and performance

The Triple Hi Kenma accommodates concrete test cylinders in the following diameters:
-
50 mm
-
100 mm
-
125 mm
-
150 mm
For standard 100 mm diameter concrete cylinders, the machine offers an approximate throughput of 45 cylinders per hour, based on 25 MPa concrete.
A typical grinding cycle takes approximately four minutes for three 100 mm diameter cylinders.
Other key features include:
-
Three-cylinder grinding capacity: Processes three specimen end surfaces simultaneously.
-
Automatic or manual operation: Provides flexibility in grinding cycle control.
-
Automatic feed and stopping: Timer-controlled operation helps maintain a consistent grinding process.
-
Diamond grinding wheel: Uses water-cooled diamond grinding technology.
-
Adjustable specimen heights: Allows three specimens of different heights to be ground simultaneously.
-
Swing-arc grinding movement: Electrically controlled wheel movement supports consistent end preparation.
-
Long grinding disc life: Approximately 25,000–60,000 cylinders under the stated 25 MPa concrete conditions.
End-face accuracy and standards
Accurate and flat specimen ends are important when preparing concrete cylinders for compressive strength testing.
The Marui Triple Hi Kenma is specified to achieve ground surface flatness within ±0.05 mm, meeting the stated requirements of AS 1012.9. Typical performance is approximately ±0.025 mm.
This level of accuracy helps provide consistent specimen end preparation and supports reliable compressive testing.
Installation and service requirements
The machine requires:
-
Electrical supply: Three-phase, 415 V, 0.75 kW
-
Cooling water: Approximately 2–3 L/min
-
Machine weight: Approximately 240 kg, wheel mounted
Its combination of throughput, accuracy and automatic operation makes it particularly suitable for laboratories processing regular volumes of concrete test cylinders.
Explore the Marui Triple Hi Kenma:
https://hyleccontrols.com.au/products/marui-cylinder-concrete-end-grinder-triple-hi-kenma
Hylec Insulated Plastic Thermal Moulds – developed for concrete laboratories

Not all concrete testing challenges involve the testing equipment itself. Temperature conditions during specimen storage and early curing can also influence concrete strength development.
Recognising this challenge, Hylec Controls undertook years of testing and development to produce our own insulated plastic moulds for concrete test cylinders.
Introduced in 2019, the moulds were designed to help moderate the temperature conditions experienced by freshly cast concrete specimens, particularly during seasonal temperature variations.
Since their introduction, we have sold more than 1,100 Hylec thermal moulds.
Our moulds are trusted by leading Australian organisations, including Boral, Hanson and Gunlake.
Why thermal insulation matters
Concrete strength development is influenced by curing temperature. In cooler conditions, early-age strength development can be slower, potentially affecting the timing of construction activities and strength testing.
Hylec insulated moulds are designed to help keep freshly cast specimens warmer in winter and cooler in summer.
By moderating temperature fluctuations, the moulds help provide more consistent conditions during the early stages of specimen curing.
This can be particularly valuable when 24-hour or early-age concrete strength results are required to support construction scheduling, post-tensioning and other time-sensitive activities.
Designed with practical laboratory features

The Hylec thermal mould has several features developed specifically for laboratory use.
Insulated plastic construction
The mould provides thermal insulation while remaining lightweight and easy to handle.
Stainless steel inner base
A stainless steel insert protects the bottom of the mould from damage during concrete placement and rodding.
Galvanised steel external base
An external galvanised steel disc allows the mould to be used with concrete sample shakers fitted with magnetic bases.
Heavy-duty insulated lid
The lid helps prevent moisture loss from the specimen while providing additional thermal insulation in hot and cold conditions.
Removable base plug
The mould incorporates a removable base plug secured with a retaining clip. Once the retaining clip and plug are removed, the specimen can be ejected using approximately 2 bar of compressed air or water.
Serial number identification
Each mould has a laser-cut serial number on its external steel base, supporting specimen and equipment identification.
Convenient handling
A separate carry handle fits beneath the mould's top flange, making it easier to transport freshly cast specimens.
Technical specifications and practical benefits
-
Suitable for 100 mm diameter concrete test cylinders.
-
Approximate mould and lid weight: 1.5 kg.
-
Sample ejection using approximately 2 bar compressed air or water.
-
Compatible with magnetic-base concrete sample shakers.
-
Expected mould service life: More than five years.
-
Lightweight construction for easier handling and transport.
-
Simple cleaning using a brush and mild organic acid.
The moulds should be oiled before use, as with conventional steel moulds. Hydrochloric acid should not be used for cleaning, as it can damage the mould material.
What did laboratory trials show?
The Hylec thermal moulds were trialled by Boral, Hanson and Cardno in Sydney.
Boral Materials Technical Services conducted a controlled trial at its Winston Hills laboratory, comparing approximately 30 concrete specimens cast in conventional steel moulds and Hylec Thermal Moulds. The trial covered standard concrete mixes, self-compacting concrete (SCC) and R53 mixes, with fresh concrete properties kept consistent to ensure a fair comparison of the two mould types. View proficiency trial
The trials reported higher concrete strengths at 1, 3 and 10 days compared with conventional moulds, with no significant difference observed at 28 days.
The moulds also achieved specimen bottom-end face flatness better than 30 microns (0.03 mm), comparable to the end-face finish obtained using a Marui grinding machine.
These results demonstrate the potential benefits of combining practical specimen mould design with effective end preparation.
Explore Hylec Insulated Plastic Moulds:
https://hyleccontrols.com.au/products/insulated-plastic-moulds-for-concrete-test-cylinders
A complete approach to concrete specimen preparation
Marui grinding machines and Hylec thermal moulds address two important stages of concrete specimen preparation.
The thermal moulds help manage early-age specimen temperature conditions, while the Marui grinder provides accurate, consistent end preparation before compressive strength testing.
Together, they offer concrete laboratories practical solutions for improving specimen preparation workflows.
| Product | Primary benefit |
|---|---|
| Marui Triple Hi Kenma | Simultaneous grinding of three concrete cylinder specimens |
| Hylec Thermal Moulds | Insulated specimen moulding and temperature moderation |
Proven products. Trusted by the concrete industry.
At Hylec Controls, we are proud of the long-standing relationships we have built with Australian and New Zealand concrete testing laboratories.
Our track record speaks for itself:
-
More than 20 years supplying Marui concrete grinding machines.
-
54 NEW Marui grinders sold over the past seven years.
-
28 NEW Marui grinders sold in the last two years.
- More than 1,100 Hylec thermal moulds sold since 2019.
We are proud to count Construction Sciences, Boral, Heidelberg Materials and Gunlake among our valued customers, and appreciate their continued trust in Hylec Controls for their concrete testing equipment and ongoing technical support.
Whether you are establishing a new concrete testing laboratory, upgrading specimen preparation equipment or looking to improve your existing workflow, Hylec Controls can help.
Looking for reliable concrete testing equipment?
Contact Hylec Controls to discuss Marui concrete cylinder grinding machines, insulated thermal moulds, spare parts and other concrete testing solutions.
Hylec Controls – Testing Solutions Since 1979.
